Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

Bmw 116i 2012 heating problems

adamhorton1991

By adamhorton1991,
in BMW 1 Series Forum

 Share

Recommended Posts

adamhorton1991 Apprentice

adamhorton1991

Posted
Posted

Hi all 

ive noticed ive lost all warm air to the drivers side and its still warm on the passenger side, i dont have dual heating,  The drivers side is only blowing cold air, its !Removed! freezing,,   and ive tried all the different vent positions ( window screen and also legs, and face vents ). 
cheers guys  

Link to comment
Share on other sites
Greydog Grand Master

Greydog

Posted
Posted

Hi Adam

Not sure about the 1 series set up but with the X5 there is a solenoid distribution valve on the nearside inner wing in the engine compartment if it sticks or one of the solenoids fails no heat (why always the driver side?) It could be the air distribution flaps sticking or broken

I would check www.realoem.com and look at the small exploded drawing see if it can give you some clues

Dave

Link to comment
Share on other sites

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 2

      650i crank no start

      Thanks for the reply Dave. This car is over 5 hours away from me so thr next trip I make needs to be the one I take it home haha. The obf2 I'm using is an mhd tuner off of my 135i with protool. I got it to connect once but stupidly disconnected it. The only code it was throwing was a immobilizer I don't remember which one. Also the conditions of the car breaking down were while driving happened 3 times than didn't start again, at least that's what I was told. So my assumption was a bmw system that controlled efi and spark ignition. As far as the cps if I was reading rpm while cranking would that not rule it out. It also did not throw a code for it when I had it connected. But I couldn't read actual position data since i couldn't connect. The owner replaced the fuel pump in an attempt to get it running so I know the pressure us there but there is absolutely no fuel coming out the cylinders or onto spark plugs. I luckily found a complete part out car 10 miles away from it. So a list of potential problems I could try would be much appreciated. Thanks Hans
      Hans fassnidge in BMW 6 Series Forum
    2. 0

      Parking Break Failure

      Hi , Just replaced rear pads on my f25 , now i have a message saying parking break failure , do i need to reset anything ? , or could i have mist something .
      Darrenscollins in Add A Suggestion
    3. 2

      650i crank no start

      Afternoon Hans Welcome to the Forum I would start with a Diagnostic Scan but then I do have ISTA/INPA on my lap top. Without it I would start by testing the sensors that will effect fuel and spark. Number one Crank position sensor if it is faulty no signal to the DME no signal to the injectors. While testing sensors Fuel Pressure sensor next, while the fuel rail is pressurised is it correct if the pressure sensor is dead the DME will assume no fuel present. Also carefully check the loom to injectors and coil packs not unknown for it to be damaged. Try a Google search for test parameters for the sensors. Also check engine earth straps Hope this helps Dave
      Greydog in BMW 6 Series Forum
    4. 1

      Suspension upgrade

      Morning Robin Welcome to the Forum By the sound of things you need a coil over kit for standard ride height with adjustable shocks. Playing with bump and rebound settings should allow a more supple ride, though wheels and tyres are a big part of the overall equation. Bilstien are a well established reliable name that has been around for years so if the kit has been developed for the car should be a good choice, lots of other kits out there with a wild price range but personally suspension tyres and brakes really are not worth cutting corners with. Dave
      Greydog in BMW 4 Series Forum
    5. 1

      Suspension upgrade

      Hello all. I have a 2019 M Sport+ 440i. I am looking for suggestions to upgrade the suspension. I do not want it lower or stiffer. I am looking for more control, predictability and less harshness. At under 20k miles, there are no faults with the factory suspension, I believe it could be better. I don't drive the car hard, its more like fast touring. I am aware of the Bilstein system that Birds BMW have developed, does anyone have experience of this system? Any alternative suggestions would be appreciated.
      Rob Charles in BMW 4 Series Forum

  • Recent Achievements


×
×
  • Create New...

Forums

News

Membership