Jump to content
Ad: Genuine BMW parts & accessories from the BMW official store on eBay ×

How To Replace Upper Bumper Grill

milleniumaire

By milleniumaire,
in BMW X5 Series Forum

 Share

Recommended Posts

milleniumaire Rookie

milleniumaire

Posted
Posted
Unfortunately my wife drove into a large bird (the feathered variety :)) at 70mph the other day and thought she had missed it until she stopped and saw the thing wedged in the front grill! It was a very messy job extracting it and unfortunately the grill has a large hole in it now.


I'm not talking about the kidney grill that is attached to the bonnet, this is one of those "cross" shaped grills nearer the bumper. There are two; a low and a high one. It is the high one, which looks like it comes in seperate parts; a left and a right. I need to replace the left grill as you look at the car from the front. I've seen some black grills on ebay, but ours is silver (titanium).


It's tricky to get to with it being behind the bumper, so I'm not sure if the bumper needs to be taken off first before replacing the grill.


I have the X5 E53 model (2004).


Can anyone please provide me with instructions on our to remove the upper bumper grill? A link to a utube video would be superb. Is it a reasonably simple job?


Also, if anyone knows where I can get a replacement from without paying BMW dealer rip-off prices, that would be great. It is a 10 year old car after all - even a second hand grill would be adequate (as long as it wasn't broken).


Thanks.

Link to comment
Share on other sites
Greydog Grand Master

Greydog

Posted
Posted

I think the bumper has to come off, I have also been told it is easy to snap the plastic clips that hold them on so take care. have you tried Quarry Motors in Sheffield they are specialist BMW breakers and have helped me a couple of times with trim bits (mirror covers, PDC sensors) Have a look at their web site to see what they have in.

Good Luck

Link to comment
Share on other sites

Latest Deals

BMW Official Store for genuine BMW parts & accessories

Disclaimer: As the club is an eBay Partner, The club may be compensated if you make a purchase via eBay links

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing




  • Latest Topics

    1. 2

      650i crank no start

      Thanks for the reply Dave. This car is over 5 hours away from me so thr next trip I make needs to be the one I take it home haha. The obf2 I'm using is an mhd tuner off of my 135i with protool. I got it to connect once but stupidly disconnected it. The only code it was throwing was a immobilizer I don't remember which one. Also the conditions of the car breaking down were while driving happened 3 times than didn't start again, at least that's what I was told. So my assumption was a bmw system that controlled efi and spark ignition. As far as the cps if I was reading rpm while cranking would that not rule it out. It also did not throw a code for it when I had it connected. But I couldn't read actual position data since i couldn't connect. The owner replaced the fuel pump in an attempt to get it running so I know the pressure us there but there is absolutely no fuel coming out the cylinders or onto spark plugs. I luckily found a complete part out car 10 miles away from it. So a list of potential problems I could try would be much appreciated. Thanks Hans
      Hans fassnidge in BMW 6 Series Forum
    2. 0

      Parking Break Failure

      Hi , Just replaced rear pads on my f25 , now i have a message saying parking break failure , do i need to reset anything ? , or could i have mist something .
      Darrenscollins in Add A Suggestion
    3. 2

      650i crank no start

      Afternoon Hans Welcome to the Forum I would start with a Diagnostic Scan but then I do have ISTA/INPA on my lap top. Without it I would start by testing the sensors that will effect fuel and spark. Number one Crank position sensor if it is faulty no signal to the DME no signal to the injectors. While testing sensors Fuel Pressure sensor next, while the fuel rail is pressurised is it correct if the pressure sensor is dead the DME will assume no fuel present. Also carefully check the loom to injectors and coil packs not unknown for it to be damaged. Try a Google search for test parameters for the sensors. Also check engine earth straps Hope this helps Dave
      Greydog in BMW 6 Series Forum
    4. 1

      Suspension upgrade

      Morning Robin Welcome to the Forum By the sound of things you need a coil over kit for standard ride height with adjustable shocks. Playing with bump and rebound settings should allow a more supple ride, though wheels and tyres are a big part of the overall equation. Bilstien are a well established reliable name that has been around for years so if the kit has been developed for the car should be a good choice, lots of other kits out there with a wild price range but personally suspension tyres and brakes really are not worth cutting corners with. Dave
      Greydog in BMW 4 Series Forum
    5. 1

      Suspension upgrade

      Hello all. I have a 2019 M Sport+ 440i. I am looking for suggestions to upgrade the suspension. I do not want it lower or stiffer. I am looking for more control, predictability and less harshness. At under 20k miles, there are no faults with the factory suspension, I believe it could be better. I don't drive the car hard, its more like fast touring. I am aware of the Bilstein system that Birds BMW have developed, does anyone have experience of this system? Any alternative suggestions would be appreciated.
      Rob Charles in BMW 4 Series Forum

  • Recent Achievements


×
×
  • Create New...

Forums

News

Membership