Jump to content

Jaymie1989

Regular Member
  • Posts

    2
  • Joined

  • Last visited

Profile Information

  • First Name
    Jaymie
  • BMW Model
    320D e90
  • BMW Year
    2006

Jaymie1989's Achievements

Newbie

Newbie (1/14)

  • First Post
  • Conversation Starter
  • Week One Done
  • One Month Later
  • One Year In

Recent Badges

0

Reputation

  1. Hi, Little bit of a back story. I purchased a E90 320D 2006 as a non runner, no only was the wrong battery in the vehicle it wasn't registered and it then there out two of the modules to start up, cas and DDE. I have rectified those. I then found that it wasn't running it's best as it would take 3-7 times to start up and the engine to stay running and not cut out. I looked into it and found that the previous owner had put petrol in the tank. There was half a tank of it so as it was running really lumpy unable to build up revs easily I imagine they filled up the tank and when it got to half empty it had issues. Anyway I have taken all the petrol out, put a new fuel filter on and changed the oil too. I've taken it out tonight for 150 miles. Whilst it smoked on start up, white smoke but cleared. I'm guessing that's just fuel burning. Anyway for the first 20/30 mins or wasn't the best I had to ride the clutch to get anywhere. When it picked up speed and going on a flat line or down hill it was good. When I put my foot down the engine did vibrate so I guess it's where it wants for fuel but it's struggling. When I done 30 miles it seemed to pull quite nicely but still lagged up hill, I'd have to shift down and really rag it. After about 60-70 miles it was absolutely fine. It didn't like being in 6th gear and driven with some acceleration. Sometimes 5th so I was going 4ty gear about 3-4 thousand revs at about 70-80mph. I ended up doing 150 miles. When idle it's still vibrating the car somewhere moderately. I'm wondering if it's an injector issue or engine mounts. I managed to get a video and a quick error code diag. Here is a link to the video. https://youtu.be/6XjQViPe76g Here is the error log of when starting the car, it did cut out twice as it hasn't been ran for a week. https://drive.google.com/file/d/16h5Z1TQh4Jb_1uT57L-Y8SoQH2Po4yqp/view?usp=drivesdk And here is the error log after the 150 mile run. https://drive.google.com/file/d/16hRAE_7dgLA1HoRc1j1eu04SeWxamkZe/view?usp=drivesdk Any help would be hugely appreciated.
  2. Hi, Hope I've put this in the right place. I have just purchased a E90 m47 320D It initially was a non runner as it didn't crank. I since found out that the previous owner had put a standard battery in. I have now put the correct battery in and resynced cme/DMS with ista d (which I'm new too) It's now starting and will run but under idle upto 1700k revs it's lumpy and shaking the whole car and struggles to stay on. I have rev'd the engine to get it to normal temperature and it sounds better after it's been left sitting for a few weeks. It first had white smoke and multiple error codes. Whilst I have cleared them some have come back straight away with some additional ones. If possible I wondered if I could get a point in the right direct. The errors I have I have scanned with Carly although I do have ista. Here is the errors I have so far. Engine / Motor Fault Code: 004A63 Fault Explanation: EWS-manipulatio Fault Code: 0044CC Fault Explanation: Boost pressure plate Fault Code: 004212 Fault Explanation: Glow plug cylinder 1, control Fault Code: 004222 Fault Explanation: Glow plug cylinder 2, control Fault Code: 004232 Fault Explanation: Glow plug cylinder 3, control Fault Code: 004242 Fault Explanation: Glow plug cylinder 4, control Fault Code: 004B10 Fault Explanation: Smoothness regulator Fault Code: 003FF0 Fault Explanation: Air flow sensor Fault Code: 004530 Fault Explanation: Boost pressure control, control deviatio I think the glow plugs were from when it tried starting and may not have been cleared correctly. I'm wondering if there is a misfire or maybe the air mass sensor that's the issue. Could anyone give me any ideas. I'm aware I might have to clear the codes and read them again.
×
×
  • Create New...

Forums


News


Membership